8 week right of return
Up to 12 year guarantee
Free & easy returns
Directly from manufacturer
B2B
My account
  • Concept R "Concert 5.1"
  • Concept R "Concert 5.1"
  • Concept R "Concert 5.1"
  • Concept R "Concert 5.1"
  • Concept R "Concert 5.1"

Concept R "Concert 5.1"

Heimkino- Säulen-Lautsprecher-Set in schöner Ahorn- bzw. Kirsche-Holz-Anmutung
Heimkino-Lautsprecher-Set mit schlanken Holz-Säulen
Columa 300 Mk2 "5.1-Set L"
Order the new generation now.
To the new generation
  • 8 week trial
  • Up to 12 year guarantee
  • Free & easy returns

Highlights

Key advantages at a glance
  • Heimkino-Lautsprecher-Set mit schlanken Holz-Säulen
  • Nur 9 cm tief - die perfekte Ergänzung zu Flachbildschirmen
  • Komponenten: 4 Stand-Säulen, 1 Center, 1 Subwoofer
  • 100 Watt Sinus-Subwoofer mit 250 mm Tieftöner
  • Passend für jeden AV-Receiver
  • Empfohlen für Räume bis 25 m²

Unser Concept R verbindet drei Eigenschaften, die so überzeugend bislang noch nie in einem einzigen Produkt zusammengefunden haben: schönes Design, schöner Klang, schöner Preis. Mit dem Concept R erhalten Sie ein komplettes 5.1-Lautsprecherset, welches extrem ansprechende Gestaltung und absolut klaren Sound verbindet, ohne dass der eine Aspekt Abstriche beim anderen erforderlich macht. Eine so ausnehmend chice Kombination mit so wohl tönendem Klangbild zu so budget-freundlichem Preis ist eine Lautsprecher Teufel-Spitzenleistung, die Ihre Freunde und Nachbarn vor Neid erblassen lassen dürfte.
       
Das Concept R besteht aus sechs Elementen: vier Säulen für Front- und Rear-Beschallung, dem Center-Lautsprecher zur Sprachübertragung und einem aktiven Subwoofer mit 100 Watt Sinus Ausgangsleistung für die Tieftonwiedergabe.

Die schlanken Satelliten des Concept R sind durch ihre interessante Farb- und Materialien-Kombination aus silbernen, schwarzen und kirschholz- oder ahornfarbenen Elementen sehr leicht harmonisch mit einer Vielzahl von Einrichtungsstilen zu kombinieren. Der magnetisch abgeschirmte querformatige Center thront im Idealfall in Nähe des Fernsehgeräts, während der Subwoofer unauffällig am Boden platziert werden kann.

Klanglich sorgt bei den Satellitensäulen des Concept R ein 25 mm Seiden-Hochtöner für eine klare und luftige Höhenwiedergabe, während gleich vier Konus-Chassis mit je 80 mm Durchmesser den für eine natürliche Stimmen- und Instrumentenwiedergabe so entscheidenden Mitteltonbereich abdecken. Diese vier Tiefmitteltöner sind genauso wie der Hochtöner auch beim Center vorzufinden, so dass durch den identischen Chassisaufbau bei Center und Satelliten ein sehr harmonisches, stimmiges Klangbild erreicht wird. Für das klangliche Fundament sorgt ein kompakter, zurückhaltend gestalteter Subwoofer, der bei entsprechenden Signalen aber gar nicht mehr so dezent, sondern kräftig zupackend mit der vollen Kraft seiner 100 Watt Sinus–Endstufe und der beachtlichen Luftverdrängung eines 250 mm-Chassis tieffrequente Signale üppig im Raum verbreitet.

Nie zuvor war eine so beeindruckende Surround-Wiedergabe in Lautsprecher Teufel-Qualität erhältlich, bei gleichzeitig ausnehmend formschönem Erscheinungsbild der Boxen! Die Zeiten in denen eine Surround-Lautsprecher-Anlage aus Preis-Gründen oder Design-Aspekten zurückgestellt werden musste, sind vorbei - dank Concept R.

Included components

  • Concept R Front/-Surroundlspeaker
  • Concept R Centerspeaker
  • Concept R Subwoofer

Downloads & support

Help regarding this product
Welcher AV-Receiver passt zum Concept R?
Auf unserer Homepage können Sie einige Empfehlungen von AV-Receivern, passend zum Concept R einsehen. In Ihre Entscheidung können Sie aber auch Nachfolgemodelle, sowie technisch gleichwertige Geräte anderer Hersteller einbeziehen.

Geräte-Empfehlungen
Can I order the Teufel speakers in different colours than those offered?
To realise the very reasonable sales prices usual for Teufel, it is not possible to offer the speakers in a multitude of housing designs.

This circumstance would drive up the production and storage costs, which would result in a significantly more expensive sales price.

A paint shop in your vicinity will surely be able to repaint the speaker housing to your preferred colour without loss of warranty - after expiry of the eight-week right of return.
Which cables do I need to connect a Teufel speaker set to the AV Receiver?
A home cinema system needs speaker cables to connect the satellite speakers to the receivers, and an NF mono RCA cable to connect the active subwoofer to the sub out socket of the AV Receiver.
My subwoofer is humming. What can I do?
This hum can be caused by the connected devices or disruptions in your electricity current. Please do a test to see which it is.

1. Remove the RCA cable from the input on the subwoofer. If the hum is no longer heard, go to point B. Otherwise, follow point A.

A. Attach the net cable of the subwoofer to another electricity outlet (i.e. Kitchen/Bathroom/Bedroom). If the subwoofer still hums, get in contact with our Support team.

Should the hum no longer be there, the disruption was a problem in your power supply, which can, for instance, be caused by dimmers or chargers. To find out where the disruption is, unplug all your devices and work back from there. As soon as the hum is heard, you now know your source of the disruption.

B. In your case, the "ground hum" is responsible for the disruption. Please proceed as follows to discover your source.

  • Disconnect the cable or satellite port from the TV Receiver and check if the hum disappears or not. If it does, you can use a sheath current filter for the cable outlet to prevent this. For example, the sheath current filter AC 9022 ED. If you have a satellite connection, connect the Satellite Receiver to the optical cable playback source - Teufel Optical Digital Cable

  • If this reason can be excluded, separate all devices from the AV Receiver one at a time until the hum stops. The last connected device is then your hum source and should be separated from the others using a galvanic separation filter (found in a retail shop)

  • If this doesn't work, get in contact with us once again so that we can give an individual, helpful response.
What is a ground hum?
The hum (50 Hz) comes from the 220 volt supply network and is caused by current power flows through the protective conductor. These so-called "ground hums" is caused when you connect two devices that are already grounded on the protective conductor (subwoofer) or the antennae cable (AV Receiver) to the subwoofer cable.

Solution:
Separate the direct connection by a grounding filter for the antennae cable that is created for it - for instance, the Teufel modell sheath current filter AC 9022 ED. Alternatively, you can use a galvanic separation filter that is looped into the connection between the subwoofer and AV Receiver.

The hum disappears if the antennae cable is separated from the Receiver/Tuner/TV. First try the grounding filter, otherwise the galvanic separation filter.
Where is the optimal place for the subwoofer of my Lautsprecher Teufel Surround System in a 5.1/6.1/7.1 configuration?
The location of a subwoofer with a recommended cut-off frequency of under/equal to 120 Hz can be freely selected and does not affect the other speakers.

Placement within the straight line between both front satellites is ideal - but not precisely in the corner of the room because certain frequency components could be unpleasantly excessive when played back.
How do I determine the right phase setting of the subwoofer?
By setting the phase, you can affect the point at which the membrane of the subwoofer bass speaker moves to the front. This setting makes it possible to optimally adjust the subwoofer to the satellites.

The membranes of the satellites should move to the front at the same time as the membrane of the subwoofer bass speaker, because all speakers of the system must vibrate in phase for optimal playback. This means that (provided the connection has the correct polarity) all drivers must move in one direction when the three front speakers receive a pulse (towards the outside or towards the inside).

If the subwoofer is in line with the front speakers, its bass speaker should have the same direction of movement (phase) - the controller on the woofer is set to "0". If the subwoofer is not between the front speakers, but is to the side of or even behind the listening location, its phase length will not match that of the front speakers. That is why the phase of the subwoofer must be changed in such cases.

So much for the theory. In practice, this means: Listen to a loud piece of music with heavy basses and ask a second person to change the phase during playback. The correct setting of the phase switch depends on where the subwoofer is positioned in the room. The position where the bass playback (above all the upper bass range) sounds the fullest is the correct position. Have fun trying it out!
What's the deal with the so-called bass traps or bass absorbers?
These are usually cubic wood housings (same MDF material as the speakers) with a bass reflex opening that have no membranes and are tuned to a certain frequency (e.g. 40 Hz as for a subwoofer). The frequency to be co-ordinated can be changed by the length and diametre of the bass reflex channel. If, for example, a room has a room resonance frequency of 28.3 Hz and this frequency is also played back in addition by a speaker/subwoofer, the room will begin to resonate at this frequency. This particular frequency is played back amplified.

This can be imagined as droning or booming, which occurs during heavy bass movie scenes such as explosions or certain types of music (Jazz, pizzicato bass). The bass absorber is then tuned exactly to this frequency so that only the speakers/subwoofer play back this frequency. The resonance frequency from the room, which would amplify this frequency, is swallowed by the bass absorber.

If you would like to damp more than one frequency (a room usually has three different frequencies: ceilings and floors, front and back and left and right, and its multiple), you will have to set up three absorbers accordingly.
How is the wattage of a subwoofer with respect to the sine wave and pulse/music performance?
Mono subwoofer:

The wattage (e.g. "360 W") printed on the rear of the subwoofer near the mains plug designates the ability of the power amplifier "to pull" a maximum power rating in the specified range at the moment of switching on (those 360 watt stated as an example).

Consequently, the wattage must correspond to at least the sine wave output of the amplifier, as this sine wave output must be permanently available which the power pack must provide as well.

The pulse/music performance of the amplifier, on the other hand, can exceed the wattage, because the short pulses are buffered additionally by the capacitors in the power pack and are not achieved solely through the performance of the power pack.

Multi-channel subwoofer:

The wattage for a multi-channel subwoofer can also be below the sine wave output, as the specified sine wave output is not requested from every channel at the same time.

For a 5 x 100 watt sinus power amplifier, for example, each of the five channels is able to implement 100 watt sine. However, not all five channels at the same time! This is also unnecessary, as the same signal is never transmitted across all five channels at the same time, thus requesting the same high sine wave output per channel.

That is why the wattage may be, e.g. 300 watt, even if the sine wave output exhibits 5 x 100 watt (= 500 watt).
Which subwoofer cables does Teufel recommend?
Dans la mesure où dans un ensemble home cinéma les caissons de basses actifs sont connectés à la sortie Out du caisson de basses du récepteur AV, un câble supplémentaire pour la connexion des enceintes satellites est nécessaire. Pour les caissons de basses actifs nous proposons deux versions de câble mono RCA NF allant de 2,5m jusque 5m. Du reste, un adaptateur Y est également disponible dans nos accessoires. Le modèle „ 2 x mâles 1 x femelle“ permet un usage complet des entrées Line-In RCA droit et gauche au caisson de basses. Ainsi, la puissance du caisson de basses s’en voit augmentée. Le modèle „1 x mâle 2 x femelles“ permet la connexion de deux caissons de basses. Une sortie caisson de basses Pre-Out du récepteur se trouve en sommes doublée.
What is room resonance frequency?
Room resonance frequency (other terms: room modes, standing waves, resonance frequency) is the frequency at which the vibrations of a voice, a musical instrument or a signal played back over the hi-fi/home cinema system is amplified unnaturally, because the vibrations build up between the walls as well as the floor and ceiling.

It is calculated of the sound velocity divided by 2 and divided by the room length [ 340 m/s: 2 : 6 m = 28.3 Hz (=1/s) ] or, more simply: 170 divided by the room dimension (length, width or height). The greatest distance between two parallel walls is taken as first standard value. For a room of 4 x 6 metres, this would be 6 metres. Strictly speaking, you would have to calculate the room resonance frequency for further parallel walls (for the 4 metres and for the ceiling height).

Overlaying resonances are also possible if the room dimensions are very close to each other. (2.8 metres high, 3 metres wide and 5.6 metres long). The resonance at 2.8 metres is repeated as multiple (times 2) at 5.6 metres length, the resonance of the 3 metres width is close to the resonance of 2.8 metres. It would resonate strongly here at 30 Hz, 56 Hz, 60 Hz and 120/112 Hz.

Phenomena of resonance frequencies:

• For example, a man with a deep voice speaks in a very small room (2 by 2 metres, 85 Hz). The voice appears to have more emphasis than in another room or out of doors. As soon as a woman speaks, the voice will sound just the same as in another room.

• The voice of a woman or that of a small child will cause glass to shatter. The voice strikes exactly the tone that corresponds to the resonant frequency of the glass. The glass resonates so strongly that it shatters (refer to the movie "The Tin Drum").

• A group of soldiers march across a bridge in cadence. The equal movement causes the bridge to vibrate so much that it collapses. That is why no one marches across bridges in cadence.
Will an active subwoofer only run in 5.1 mode or also in stereo mode?
Thanks to the speaker set-up/bass management integrated in the home cinema receivers/amplifiers, the subwoofer functions in stereo, Dolby Surround and digital mode.

The corresponding setting in the speaker set-up must be adjusted individually for each source for many receivers, however, e.g. for CD playback only front without woofer, and front speakers plus woofer for Dolby Surround video playback.
Why doesn't my active subwoofer switch on automatically?
Some AV Receivers/amplifiers issue the bass signals via the subwoofer pre-amplifier output so quietly that the subwoofer does not start automatically.

To make sure the subwoofer switches on and off correctly in automatic mode, (to be selected on the corresponding switch of the subwoofer, such as "Auto / On / Off"), we recommend turning the level control on the subwoofer to 1/3 or perhaps to 1/2 and increasing the output level for the sub in the receiver's speaker set-up – sometimes up to the maximum (+10 dB or +12 dB). The subwoofer should then work perfectly.

The maximum position of the output level in the speaker set-up of the AV Receiver is obligatory for some of our models (e.g. the Concept S subwoofer).
How do I connect my fully active Teufel system to an AV Receiver?
Although designed to be fully active, the Teufel set is also partially active in conjunction with an AV Receiver.

You can connect it like a standard speaker system: the five satellites via speaker cable to the corresponding speaker outputs front R/L, rear R/L and centre of the AV Receiver/amplifier and the subwoofer from the front R input via a mono-RCA cable to the Sub Out output on the A/V Receiver/amplifier.

Please note:
The auto on/standby switch only responds when the front R input is being used! The subwoofer also receives the full subwoofer signal via this channel.

If the AV Receiver/amplifier has preamplifier outputs for all channels (front R/L, rear R/L, centre and subwoofer), the Teufel set can also be connected via three RCA cable pairs to the subwoofer and the satellites via speaker cables to the subwoofer. However, we recommend using the first version.
What is the use of the on/off automatic switch ("Auto On/Off") of the active subwoofer?
The On/Off switch is a power-saving standby switch. The switch must be set to "On" or "1" to activate the standby. The subwoofer is activated as soon as it receives a strong bass signal. After approx. ten to twenty minutes of no signal, or only after receiving a very weak signal, it automatically switches to the standby function.

Even though the LED is still illuminated, the subwoofer is in standby mode. This function can be easily checked by slowly increasing the volume at the receiver/amplifier. You will hear a quiet popping noise when the subwoofer activates itself as of a certain level.
What happens to the power amplifiers of the subwoofer if I don't connect the satellites?
As soon as the satellites are connected to the subwoofer and not to the AV Receiver/amplifier, the performance of the 6 or 8-channel power amplifier is distributed to the subwoofer and to the satellites.

If the satellites are not connected directly to the subwoofer but to the AV Receiver/amplifier via speaker cable instead, the subwoofer performance will increase somewhat; the power amplifiers for the satellites have no function. This enables the subwoofer and satellites to play even more dynamically than if the subwoofer still had to provide the satellites with performance.

The technical background: The subwoofer has a large transformer with a specific wattage. This performance is either distributed to the five satellites and the subwoofer, or you receive a higher performance only for the subwoofer.
How can I connect an additional active subwoofer?
If your receiver has only one subwoofer output ("Sub Out"), you only need a monocinch cable, which is then connected from the receiver to the "Sub In" of the subwoofer. With two subwoofer outputs, you can order a so-called Y-adapter from the Teufel accessories page, which has a cinch plug on one side and two cinch (RCA) sockets on the other. Connect the plug to the subwoofer "Pre Out" on the AV receiver/amplifier and connect the mono cinch cable to the two subwoofers.

If the cabling method is easier for you, then you can alternatively connect one subwoofer to the other. You will need two mono cinch cables - one to connect the subwoofer "Pre Out" on the AV receiver/amplifier to the left line-in input of the first subwoofer, and the other to connect the left line-out output of the first subwoofer to the left line-in input of the second subwoofer.
What are the volume switches for?
The sound of the speaker always depends on the room where it is located.

The volume of the active subwoofer can be controlled so that you can adapt the relationship between the active bass and treble / mid tones to suit the room.

Use your own senses to judge which settings sound best in your room. This switch is especially useful in stereo mode. On the other hand, multichannel amplifiers often have technologies that adjust the subwoofer volume - so when using a multichannel amplifier the controller should first be set at 0dB.
Cookies are used on our website
In order to provide the best possible service and to offer relevant advertisements, we use functional, analytical and advertising cookies, as well as similar technologies provided by Teufel Audio or third parties, on our site. For more information, please see our Privacy Policy and Cookie Guidelines, where you can manage your cookie settings and opt-out. By clicking the X symbol, or by continuing to use this website (for example, by clicking a link on the site), you consent to the use of these cookies.