Cinebar 11 "2.1-Set"

It could be that the speaker is connected as a device with speakerphone function. Please go to: settings menu > devices and printer > BOOMSTER (or other Bluetooth device). Right click on the device and remove the check mark next to the “speakerphone” option.

Unfortunately, the operating instructions for the Cinebar 11 contain a mistake on page twelve where it is stated that the soundbar and subwoofer pair with each other automatically.
While this is essentially correct – the soundbar and subwoofer do automatically pair with each other when switched on – this only happens after an initial setup procedure. To pair the two devices for the first time, please proceed as follows:
1) Connect the soundbar and subwoofer to power.
2) Press the “Menu” button on the Cinebar 11’s remote control. Next, go to the menu option “WS” and confirm your selection by pressing the “OK” button.
3) Press “OK” again in order to access the menu option “LINK” and then “START”. The word “SEARCH” will appear on the Cinebar 11’s display.
4) Next, press the button on the back of the subwoofer marked “Pairing”.
5) Both devices are now connected. Once the status “OK” appears on the soundbar’s display, both devices will be permanently connected. The pairing procedure now takes place automatically whenever both devices are turned on.

This hum can be caused by the connected devices or disruptions in your electricity current. Please do a test to see which it is.

1. Remove the RCA cable from the input on the subwoofer. If the hum is no longer heard, go to point B. Otherwise, follow point A.

A. Attach the net cable of the subwoofer to another electricity outlet (i.e. Kitchen/Bathroom/Bedroom). If the subwoofer still hums, get in contact with our Support team.

Should the hum no longer be there, the disruption was a problem in your power supply, which can, for instance, be caused by dimmers or chargers. To find out where the disruption is, unplug all your devices and work back from there. As soon as the hum is heard, you now know your source of the disruption.

B. In your case, the "ground hum" is responsible for the disruption. Please proceed as follows to discover your source.

• Disconnect the cable or satellite port from the TV Receiver and check if the hum disappears or not. If it does, you can use a sheath current filter for the cable outlet to prevent this. For example, the sheath current filter AC 9022 ED. If you have a satellite connection, connect the Satellite Receiver to the optical cable playback source - Teufel Optical Digital Cable


• If this reason can be excluded, separate all devices from the AV Receiver one at a time until the hum stops. The last connected device is then your hum source and should be separated from the others using a galvanic separation filter (found in a retail shop)


• If this doesn't work, get in contact with us once again so that we can give an individual, helpful response.

Thanks to the speaker set-up/bass management integrated in the home cinema receivers/amplifiers, the subwoofer functions in stereo, Dolby Surround and digital mode.

The corresponding setting in the speaker set-up must be adjusted individually for each source for many receivers, however, e.g. for CD playback only front without woofer, and front speakers plus woofer for Dolby Surround video playback.

Some AV Receivers/amplifiers issue the bass signals via the subwoofer pre-amplifier output so quietly that the subwoofer does not start automatically.

To make sure the subwoofer switches on and off correctly in automatic mode, (to be selected on the corresponding switch of the subwoofer, such as "Auto / On / Off"), we recommend turning the level control on the subwoofer to 1/3 or perhaps to 1/2 and increasing the output level for the sub in the receiver's speaker set-up – sometimes up to the maximum (+10 dB or +12 dB). The subwoofer should then work perfectly.

The maximum position of the output level in the speaker set-up of the AV Receiver is obligatory for some of our models (e.g. the Concept S subwoofer).

1. You take the load off of your amplifier/receiver and thus receive more dynamics.

2. The active subwoofer makes it possible to set the volume separately from the remaining speakers.

3. Only an active subwoofer can be connected directly to the subwoofer connection of a home cinema receiver.

Although designed to be fully active, the Teufel set is also partially active in conjunction with an AV Receiver.

You can connect it like a standard speaker system: the five satellites via speaker cable to the corresponding speaker outputs front R/L, rear R/L and centre of the AV Receiver/amplifier and the subwoofer from the front R input via a mono-RCA cable to the Sub Out output on the A/V Receiver/amplifier.

Please note:
The auto on/standby switch only responds when the front R input is being used! The subwoofer also receives the full subwoofer signal via this channel.

If the AV Receiver/amplifier has preamplifier outputs for all channels (front R/L, rear R/L, centre and subwoofer), the Teufel set can also be connected via three RCA cable pairs to the subwoofer and the satellites via speaker cables to the subwoofer. However, we recommend using the first version.

The hum (50 Hz) comes from the 220 volt supply network and is caused by current power flows through the protective conductor. These so-called "ground hums" is caused when you connect two devices that are already grounded on the protective conductor (subwoofer) or the antennae cable (AV Receiver) to the subwoofer cable.

Solution:
Separate the direct connection by a grounding filter for the antennae cable that is created for it - for instance, the Teufel modell sheath current filter AC 9022 ED. Alternatively, you can use a galvanic separation filter that is looped into the connection between the subwoofer and AV Receiver.

The hum disappears if the antennae cable is separated from the Receiver/Tuner/TV. First try the grounding filter, otherwise the galvanic separation filter.

The location of a subwoofer with a recommended cut-off frequency of under/equal to 120 Hz can be freely selected and does not affect the other speakers.

Placement within the straight line between both front satellites is ideal - but not precisely in the corner of the room because certain frequency components could be unpleasantly excessive when played back.

By setting the phase, you can affect the point at which the membrane of the subwoofer bass speaker moves to the front. This setting makes it possible to optimally adjust the subwoofer to the satellites.

The membranes of the satellites should move to the front at the same time as the membrane of the subwoofer bass speaker, because all speakers of the system must vibrate in phase for optimal playback. This means that (provided the connection has the correct polarity) all drivers must move in one direction when the three front speakers receive a pulse (towards the outside or towards the inside).

If the subwoofer is in line with the front speakers, its bass speaker should have the same direction of movement (phase) - the controller on the woofer is set to "0". If the subwoofer is not between the front speakers, but is to the side of or even behind the listening location, its phase length will not match that of the front speakers. That is why the phase of the subwoofer must be changed in such cases.

So much for the theory. In practice, this means: Listen to a loud piece of music with heavy basses and ask a second person to change the phase during playback. The correct setting of the phase switch depends on where the subwoofer is positioned in the room. The position where the bass playback (above all the upper bass range) sounds the fullest is the correct position. Have fun trying it out!