Cinebar 50 SE
- 8 week trial
- Up to 12 year guarantee
- Free & easy returns
Overview of our technologies
Cinebar® 50 improves your TVs sound quality dramatically. There's more, though. This fully fledged sound system supports the Dolby Virtual Speaker technology and can be used for DVD, Blu-ray, satellite/premiere/DVB-T-decoder playback, in stereo and spatial sound.
Modern flat screen televisions have plenty of advantages. Sound quality, however, isn't often one of them. Enter the Cinebar® 50, an elegant and complete solution which will outclass any flat screen's flimsy factory sound. Enjoy improved dialog renditions, dynamics, higher volume, and spatial acoustics surround sound.
Spatial sound from a single speaker
You'll be astonished when you hear the Cinebar® 50's virtual spatiality. That's because the system features the Dolby virtual speaker technology developed over years of meticulous research and development. It processes sound signals in a very special way, distributing them over the built-in speaker chassis. The resulting sound nearly replicates standard five-speaker surround sound.
Cinebar® 50 is an ensemble. It's the simplest way to upgrade your flat-screen's sound without having to assemble an entire loudspeaker system in your living room. Power reserves of 350-watts RMS make this one of the highest-performing systems of this class available today. Save space and skip the hassle without compromising sound quality. Teufel makes it possible.
Das langhubige, mit Klippel-Messtechnik optimierte 250 mm-Tieftonchassis, ein großzügig dimensioniertes Bassreflex-Gehäuse mit 32 Liter Volumen und eine neue 100 Watt Sinus-Endstufe sorgen für eine in dieser Preisklasse unerreichte Basswiedergabe bis hinab auf 34 Hz. Der interne Limiter schützt vor Übersteuerungen und Verzerrungen.
Ein Frontschalter ermöglicht die direkte Inbetriebnahme. Die Empfindlichkeit des Standby-Modus ist auf der Rückseite regulierbar. Vier Resonanzdämpfer-Füße gewährleisten den sicheren Stand und eine Entkoppelung vom Boden.
Der US 5110/SW mit schwarz glänzender Frontpartie ist nicht separat erhältlich.
- Subwoofer US 5110/1 SW
- Soundbar Cinebar 50
- Mono RCA cable for Cinebar 50
- Remote Control CB 50 RC
- Angle Bracket Adapter Cinch for Cinebar 50
- Angle Bracket Adapter Optical for Cinebar 50
Loudspeaker, decoder, preamplifier, and power amp.
The Cinebar 50 unit is equipped with two tweeters, two mid-range drivers, and two low-mid-range drivers that act as a two-and-a-half-way configuration. Together with an integrated amplifier, this speaker system provides 200 watts RMS power.
Two digital (optical/coaxial) and two analogue inputs, plus a USB port located on the front of the speaker for MP3 or WMA formats, await four source devices and sound files.
Cinebar 50’s decoder component processes Dolby Digital and dts signals originating from incoming digital input devices. This decoder element converts the signal into the proper format for playbac on this stereo device, using Dolby Virtual speaker technology to generate a virtual surround-sound effect. Three different playback modes are available:
Stereo – Wide – Reference.
The ergonomic remote control allows you to easily access the most important control functions. The current settings status can be easily read off the sound bar panel.
The Cinebar 50 module comes with two brackets located at the back of the speaker which can be used to mount the speaker directly to the wall. A table stand for placing it to TV furniture is included in the shipment.
|Tweeter (number per enclosure)||2|
|Tweeter (diameter)||25.00 mm|
|Midrange driver (number per enclosure)||2|
|Midrange driver (diameter)||100.00 mm|
|Midrange driver (material)||Cellulose. coated|
|Bass/Midrange driver (number per enclosure)||2|
|Bass/Midrange driver (diameter)||100.00 mm|
|Bass/Midrange driver (material)||Cellulose. coated|
|Digital inputs coaxial||1|
|Digital inputs optical||1|
|Cinch input stereo||2|
|Bass driver output||1|
|Dolby Pro Logic||Yes|
|Dolby Pro Logic II||Yes|
|Dolby Pro Logic II||Movie, Music, Game|
|Dolby Virtual Speaker||Yes|
|Amplifier technology||Class D|
|Power output capacity sinus (RMS) Satellite||100 W|
The front control allows for the subwoofer to be turned on immediately, and the sensitivity of its standby mode can be regulated on its rear panel.
Four resonance-dampening feet ensure solid placement and isolate it from the floor. The US 5110/SW is black with a glossy black front plate and is only available as part of a set.
|Woofer (diameter)||250.00 mm|
|Enclosure type||Bass reflex|
|Net internal volume||32 Litres|
|Lowest frequency (-3 dB)||34 Hz|
|Phase control||on/off, 0 or 180 degrees|
|Power output capacity sinus (RMS) Bass||100 W|
|Standby-Power consumption||0.34 watt|
|Maximum power consumption||285 watt|
|Miscellaneous||Variable switch - Auto On/Off|
|Miscellaneous||The height was measured without the stand feet. The height of the stand feet is 12 mm.|
Downloads & support
For Theater 2 and larger systems, we recommend the Teufel cable with 4 mm² cross-section for the front/centre speakers, and the 2.5 mm² cable up to a length of 15 metres for the effect speakers.
Choose a higher cross-section for even greater lengths.
Fully active set do not necessarily need an AV Receiver. The five to seven satellite speakers here are supplied with power by the amplifiers which are installed in the subwoofer in addition to the subwoofer power amplifier. This saves you the costs of a receiver, but it is usually only possible to connect one source to our fully active subwoofer.
Exceptions here are the Concept E2, the Concept E Magnum Digital, the Motiv 5 Digital, the Concept F, the LT2+R and the Concept S+R.
Naturally you can also equip the fully active systems with an AV Receiver at a later point. The connection is then equal to the partially active sets.
Modern AV Receivers offer numerous options for compensating electronically for any compromises in the set up. Generally speaking, the following rule always applies: you can always use our recommendations as a basis for experimenting with what works best for you, acoustically and optically. Let your ears (and eyes) decide!
This circumstance would drive up the production and storage costs, which would result in a significantly more expensive sales price.
A paint shop in your vicinity will surely be able to repaint the speaker housing to your preferred colour without loss of warranty - after expiry of the eight-week right of return.
1. Remove the RCA cable from the input on the subwoofer. If the hum is no longer heard, go to point B. Otherwise, follow point A.
A. Attach the net cable of the subwoofer to another electricity outlet (i.e. Kitchen/Bathroom/Bedroom). If the subwoofer still hums, get in contact with our Support team.
Should the hum no longer be there, the disruption was a problem in your power supply, which can, for instance, be caused by dimmers or chargers. To find out where the disruption is, unplug all your devices and work back from there. As soon as the hum is heard, you now know your source of the disruption.
B. In your case, the "ground hum" is responsible for the disruption. Please proceed as follows to discover your source.
- Disconnect the cable or satellite port from the TV Receiver and check if the hum disappears or not. If it does, you can use a sheath current filter for the cable outlet to prevent this. For example, the sheath current filter AC 9022 ED. If you have a satellite connection, connect the Satellite Receiver to the optical cable playback source - Teufel Optical Digital Cable
- If this reason can be excluded, separate all devices from the AV Receiver one at a time until the hum stops. The last connected device is then your hum source and should be separated from the others using a galvanic separation filter (found in a retail shop)
- If this doesn't work, get in contact with us once again so that we can give an individual, helpful response.
Tauschen Sie die neben dem Netzschalter befindliche Sicherung aus. Falls die Power-Diode danach nicht leuchtet, wenden Sie sich bitte an unseren Service. Falls die Power-Diode danach leuchtet, aber kein Ton zu vernehmen ist, verfahren Sie bitte wie unter Punkt 2. beschrieben.
2. Falls die Power-Diode leuchtet:
Drehen Sie den Pegelregler Level am Subwoofer auf »Minimum«, ziehen das Subwoofer-Cinchkabel am Verstärker ab, drehen Level vorsichtig hoch und berühren den Cinch-Heißleiter des Cinch-Kabels (innen) mit dem Finger. Ist nun ein Brummen oder Knacken zu hören, liegt der Fehler beim Receiver oder seinen Einstellungen. Bleibt der Subwoofer stumm, wenden Sie sich bitte an unseren Service.